引用本文:郭永明， 朱胜， 宋占永， 于鹤龙， 魏敏， 陈洁.亚音速火焰喷涂铝硅/聚苯酯涂层的组织与摩擦学性能[J].中国表面工程,2016,29(2):85~90
GUO Yongming, ZHU Sheng, SONG Zhanyong, YU Helong, WEI Min, CHEN Jie.Microstructure and Friction Behavior of AlSi/Polyester Composited Coating Prepared by Subsonic Flame Spraying[J].China Surface Engineering,2016,29(2):85~90
【打印本页】   【HTML】   【下载PDF全文】   【查看/发表评论】  【EndNote】   【RefMan】   【BibTex】
←前一篇|后一篇→ 过刊浏览    高级检索
本文已被：浏览 4780次   下载 3596次 本文二维码信息
码上扫一扫！
分享到： 微信 更多
字体:加大+|默认|缩小-
亚音速火焰喷涂铝硅/聚苯酯涂层的组织与摩擦学性能
郭永明， 朱胜， 宋占永， 于鹤龙， 魏敏， 陈洁1,2
1. 装甲兵工程学院 再制造技术重点实验室;2. 北京福锐克森热喷涂科技有限公司
摘要:
为开发先进的铝基固体自润滑材料与技术，采用亚音速火焰喷涂技术制备了铝硅/聚苯酯涂层，利用扫描电子显微镜（SEM）、电子能谱仪（EDS）、洛氏硬度计、拉伸试验机、摩擦磨损试验机分析测试了涂层的组织、硬度与结合强度，探讨了载荷对涂层摩擦学性能的影响。结果表明，涂层由铝硅和聚苯酯相构成，聚苯酯相所占面积比约20%。涂层组织致密，与基体结合强度达67 MPa，表面宏观硬度约为75.3 HR15Y。试验载荷对铝硅/聚苯酯涂层的摩擦学性能有显著影响，涂层摩擦因数随载荷的上升呈先下降后上升趋势，不同载荷致使涂层在组织、成分、形态等方面的差异是其主要影响因素。
关键词:  亚音速火焰喷涂； 铝硅/聚苯酯  复合涂层； 摩擦学性能
DOI：10.11933/j.issn.1007-9289.2016.02.012
分类号:
基金项目:
Microstructure and Friction Behavior of AlSi/Polyester Composited Coating Prepared by Subsonic Flame Spraying
GUO Yongming, ZHU Sheng, SONG Zhanyong, YU Helong, WEI Min, CHEN Jie1,2
1. Science and Technology on Remanufacturing Laboratory, Academy of Armored Forces Engineering;2. Beijing Fu Rui Ke Sen Thermal Spraying Technology Co., LTD.
Abstract:
To develop the advanced Albased solid selflubricating material and technology, AlSi/Polyester composited coating was prepared by subsonic flame spraying technology. The microstructure, chemical composition, macro hardness and bonding strength of the coating were investigated with scanning electron microscope (SEM), energy dispersive spectrometer (EDS), Rockwell hardness tester and tensile testing machine, respectively. Moreover, the effect of load on the tribological behaviors of the coating was studied using a ballondisc tribometer. Results show that the coating consists of two different phases of AlSi and polyester, and the area ratio of the later phase in coating crosssection is about 20%. It possesses a macro hardness of 75.3 HR15Y and exhibits a dense structure with a good bonding strength about of 67 MPa. The applied load has a significant impact on the tribological behaviors of the coating. The friction coefficient of the coatin first decreases and then increases with the increase of the load. This might be due to the different microstructures, contents and micrographs of the coating caused by different loads.
Key words:  subsonic flame spraying  AlSi/Polyester  composited coating  friction behavior
手机扫一扫看